المعادلة
t = TMS × 0.14 / (M^0.02 − 1)، حيث M = I / Is، أي تيار العطل مقسومًا على تيار الالتقاط (Pickup current)، وTMS معامل الزمن (Time Multiplier Setting). ومعنى المعادلة أن الزمن يقصر كلما زاد التيار، ولهذا سُمّي المنحنى عكسيًا. ومعاملات المنحنيات الأخرى في حاسبة المنحنيات.
المثال
- المرحّل الأقرب (R1): تيار الالتقاط (Pickup) 400 أمبير وTMS = 0.1.
- المرحّل الأعلى (R2): تيار الالتقاط 600 أمبير، وTMS هو المطلوب.
- أقصى تيار عطل عند R1: 4000 أمبير، ويمر في المرحّلين.
- هامش التنسيق المطلوب (Grading margin): 0.3 ثانية.
الحساب
- R1:
M = 4000 / 400 = 10، فالزمن0.1 × 0.14 / (10^0.02 − 1) ≈ 0.297ثانية. - زمن R2 المطلوب:
0.297 + 0.3 = 0.597ثانية على الأقل. - R2 عند 4000 أمبير:
M = 4000 / 600 ≈ 6.67، والزمن عند TMS = 1 هو0.14 / (6.67^0.02 − 1) ≈ 3.62ثانية. - إذن
TMS ≥ 0.597 / 3.62 ≈ 0.165. ولأن الضبط (Setting) يتغير بدرجات، نختار أقرب درجة أعلى وهي 0.175، فيكون زمن R2 نحو 0.634 ثانية والهامش نحو 0.34 ثانية.
ولماذا نحسب الهامش عند أقصى تيار عطل يمر في المرحّلين؟ لأن المنحنيين يتقاربان كلما زاد التيار، فإذا تحقق الهامش هناك تحقق عند ما دونه. وعند التيارات الأقل يكون الهامش أكبر، ومع ذلك يحسن التحقق منه عند أدنى تيار عطل أيضًا.
من أين تأتي 0.3 ثانية؟
- زمن فتح قاطع (Circuit Breaker) R1 حتى انقطاع تيار العطل (Fault clearing).
- تجاوز R2 (Overshoot): أي ما يستمر فيه المرحّل بعد زوال التيار.
- خطأ التوقيت في المرحّلين وخطأ محولات التيار (CT).
- هامش أمان (Safety margin).
ولهذا يختلف الرقم باختلاف المعدات: فمع المرحّلات الرقمية (Numerical relays) والقواطع الحديثة يشيع 0.3 ثانية أو أقل، ومع المرحّلات الكهروميكانيكية (Electromechanical) 0.4 ثانية أو أكثر. والرقم في النهاية قرار المهندس وفق المعدات وممارسة الجهة.
وبعد الحدث
الحساب يقول ما يُفترض أن يحدث، أما تسجيل العطل (Fault record) فيبيّن ما حدث فعلًا: من التقط (Pickup)، ومن أرسل إشارة الفصل (Trip)، ومتى انقطع تيار العطل. فإن فصل المرحّل الأعلى قبل الأقرب، أو بهامش أقل من المحسوب، فالتسجيل هو الدليل. ارفعه في المنصة لترى تسلسل الأحداث (SOE) والأزمنة.
الأزمنة نظرية من المعادلة. راجع إعدادات المرحّل الفعلية ومنحنى الصانع قبل اعتماد أي قيمة.
The formula
t = TMS × 0.14 / (M^0.02 − 1), with M = I / Is (fault current over pickup). Constants for the other curves are in the curve calculator.
The example
- Nearer relay (R1): pickup 400 A, TMS = 0.1.
- Upstream relay (R2): pickup 600 A; its TMS is what we want.
- Maximum fault current at R1: 4000 A, flowing through both relays.
- Required margin: 0.3 s.
Working
- R1:
M = 4000 / 400 = 10, sot = 0.1 × 0.14 / (10^0.02 − 1) ≈ 0.297s. - R2 must take at least
0.297 + 0.3 = 0.597s. - R2 at 4000 A:
M = 4000 / 600 ≈ 6.67, and the time at TMS = 1 is0.14 / (6.67^0.02 − 1) ≈ 3.62s. - So
TMS ≥ 0.597 / 3.62 ≈ 0.165. Taking the next step up, 0.175, R2 takes about 0.634 s and the margin is about 0.34 s.
The margin is checked at the maximum fault current through both relays, because the curves get closer as current rises. At lower currents the margin is larger; it is worth checking at the minimum fault current too.
Where 0.3 s comes from
- R1's breaker opening time, until fault current is interrupted.
- R2's overshoot: how long it keeps going after the current is gone.
- Timing errors in both relays and CT errors.
- A safety margin.
With numerical relays and modern breakers 0.3 s or less is common; with electromechanical relays 0.4 s or more. The figure is the engineer's call, for the equipment and the utility's practice.
After the event
A fault record shows what actually happened: who picked up, who sent the trip and when fault current was interrupted. If the upstream relay tripped before the nearer one, or with less margin than worked out, the record is the evidence. Upload it to the platform to see the event sequence and timings.
Times are theoretical, from the formula. Check the relay's actual settings and the maker's curve before relying on any value.